DSC 4 Zone Keypad

System indicator lights on the keypad, and keypad is beeping (to silence the beeps, press the [ # ] key):

Press [ * ]+[2] to display one of the following trouble conditions:

If the zone 1 indicator lights- This indicates your backup battery is low or disconnected. This could be a normal indication after a power outage, and if so, should correct itself within 24 hrs. If you have not had any power outages in the last 24 hours, it may indicate that the battery needs to be replaced by a service technician.

If the zone 2 indicator lights- This indicates that the AC power is out. This could be because of a Electric Service outtage (there would be no power in the house), or possibly a house fuse is blown or circuit breaker is tripped. If you have verified that all house circuits are OK, but the trouble condition does not correct itself, please call for a service technician.

If the zone 4 indicator lights- This indicates that the alarm panel is unable to communicate with the central station. Often this is caused by a loss of telephone service, or if someone or something is using the phone when the system tried to communicate with the central staton. The alarm system will retry many times. If your phone service has not been interrupted, and this indication does not clear itself shortly, please call for a service technician.

If your keypad is displaying indications other than listed here, please contact our service department.

After diagnosis above use the [ # ] key to return to ready condition. To reset the keypad, press the [ * ] key then press and hold down the [ 4 ] key for 5 seconds.

DSC 6 Zone Keypad

System indicator lights on the keypad, and keypad may beep twice every 10 seconds (to silence the beeps, press the [ # ] key):

Press [ * ]+[2] to display one of the following trouble conditions:

If the zone 1 indicator lights- This indicates your backup battery is low or disconnected. This could be a normal indication after a power outage, and if so, should correct itself within 24 hrs. If you have not had any power outages in the last 24 hours, it may indicate that the battery needs to be replaced by a service technician.

If the zone 2 indicator lights- This indicates that the AC power is out. This could be because of a Electric Service outtage (there would be no power in the house), or possibly a house fuse is blown or circuit breaker is tripped. If you have verified that all house circuits are OK, but the trouble condition does not correct itself, please call for a service technician.

If the zone 3 indicator lights- This indicates the DC power supply inside the alarm system has a blown fuse, this will cause any devices (motion detectors, glass break detectors, etc.) not to function. Please contact our service technicians to set up a repair date time.

If the zone 4 indicator lights- This indicates that the alarm panel is unable to communicate with the central station. Often this is caused by a loss of telephone service, or if someone or something is using the phone when the system tried to communicate with the central staton. The alarm system will retry many times. If your phone service has not been interrupted, and this indication does not clear itself shortly, please call for a service technician.

If the zone 5 indicator lights- This indicates your fire zone on your system is in need of repair. This may mean the fire zone will not cause an alarm, or could cause a false alarm. Please contact our service technicians.

If the zone 6 indicator lights- This indicates that the system clock has been reset, usually caused by a combination of no AC & battery backup power. You may also have an indication of a low backup battery and/or no AC power. This will normally be reset within 24 hours when your system calls in (as it does every day). Please contact our service technicians if this condition does not go away within 24 hours.

If your keypad is displaying indications other than listed here, please contact our service department.

After diagnosis above use the [ # ] key to return to ready condition. To reset the keypad, press the [ * ] key then press and hold down the [ 4 ] key for 5 seconds.

DSC 8 or more Zone Keypad

System indicator lights on the keypad, and keypad may beep twice every 10 seconds (to silence the beeps, press the [ # ] key):

Press [ * ]+[2] to display one of the following trouble conditions:

If the zone 1 indicator lights- This indicates your backup battery is low or disconnected. This could be a normal indication after a power outage, and if so, should correct itself within 24 hrs. If you have not had any power outages in the last 24 hours, it may indicate that the battery needs to be replaced by a service technician.

If the zone 2 indicator lights- This indicates that the AC power is out. This could be because of a Electric Service outtage (there would be no power in the house), or possibly a house fuse is blown or circuit breaker is tripped. If you have verified that all house circuits are OK, but the trouble condition does not correct itself, please call for a service technician.

If the zone 4 indicator lights- This indicates that the alarm panel is unable to communicate with the central station, specifically the system is unable to get a dial tone on the phone line. Please verify you are able to get a dial tone on all phone lines in your house. If your phone service has not been interrupted, please call for a service technician.

If the zone 5 indicator lights- This indicates that the alarm panel is unable to communicate with the central station. Often this is caused by a loss of telephone service, or if someone or something is using the phone when the system tried to communicate with the central staton. The alarm system will retry many times. If your phone service has not been interrupted, and this indication does not clear itself shortly, please call for a service technician.

If the zone 6 indicator lights- This indicates that the system siren or bell has a problem, and may not sound in the case or an alarm condition. Please contact our service technicians.

If the zone 7 indicator lights- This indicates your fire zone on your system is in need of repair. This may mean the fire zone will not cause an alarm, or could cause a false alarm. Please contact our service technicians.

If the zone 8 indicator lights- This indicates that the system clock has been reset, usually caused by a combination of no AC & battery backup power. You may also have an indication of a low backup battery and/or no AC power. This will normally be reset within 24 hours when your system calls in (as it does every day). Please contact our service technicians if this condition does not go away within 24 hours.

If your keypad is displaying indications other than listed here, please contact our service department.

After diagnosis above use the [ # ] key to return to ready condition. To reset the keypad, press the [ * ] key then press and hold down the [ 4 ] key for 5 seconds.

Troubleshooting

KEY PAD WILL NOT TAKE CODE:
If the keypad will not accept your passcode, press [#] to clear previous entries and try again.

MEMORY LIGHT IS ON:
If the 'Memory' light is on, it means an alarm has occurred. Press [*]+[3], the zone light will display to indicate which zone caused the alarm. Press [#] to return to ready condition. Arming and disarming the system will clear the memory light.
Important Note:If you return to the premises and find that an alarm is in progress or that there are alarms in memory, do not enter the premises as an intruder may be present. Go to a neighbor and contact the local authorities from there.

BYPASSING ZONES:
To bypass a zone, press [*]+[1] and then press the zone you wish to bypass. Press [#] to return to ready. The zone light for the zone(s)you just bypassed will remain on. Arm system as normal, the next time you disarm the system, it will automatically clear out any bypassed zones.

CHIME FEATURE:
This causes the keypad to chime when a door is opened and the system is disarmed. Enter[*]+[6]+[MASTER CODE]+[6] to turn this feature ON or OFF. If keypad beeps 3 times, the chime feature is enabled, or one long beep if disabled. This feature will remain in effect through arming and disarming cycles. Press [#] to return to ready condition.

ARMING YOUR SYSTEM:
1. Before arming the system, ensure all protected doors and windows are closed, stop any movement in areas protected by motion detectors. When all zones are closed, all of the Zone Lights on the keypad will be OFF, and the "Ready" light will be ON.
2. To arm the system, enter a 4-digit Access Code. As each digit is entered, the keypad sounder will beep. When the Access Code has been entered, the "Armed" light will come ON and the keypad will beep 6 times. If an incorrect Access Code is entered, the keypad will sound a single long tone. To correct a mistake when entering a code, press the [#] key, and enter the code again.
3. When the "Armed" light comes ON, leave the premises through the designated Entry-Exit door before the Exit Delay expires. At the end of the Exit Delay, all lights on the keypad will shut OFF except for the "Armed" light- your system is now armed.

DISARMING YOUR SYSTEM:
1. Enter the premises through the designated Entry-Exit door. The keypad will sound a constant tone to indicate that the system must be disarmed.
2. Go to the keypad and enter your Access Code. If you make a mistake when entering a code, press the [#] key, and enter the code again. A correct Access Code must be entered before the Entry Delay expires or an alarm will sound.
3. When a correct Access Code is entered, the "Armed" light will be shut OFF, and the sounder will be silenced- your system is now disarmed.
4. If an alarm occurred while the system was armed, the "System" light and the Zone Lights of the Zones that went into alarm will FLASH for two minutes. Press the [#] key to cancel the flashing display and return the keypad to the "Ready" mode. The "Memory" light will now be lit until the next time you arm the system (see "Memory Light is on" above).
Important Note:If you return to the premises and find that an alarm is in progress or that there are alarms in memory, do not enter the premises as an intruder may be present. Go to a neighbor and contact the local authorities from there.

KEYPAD SOUNDER TONE:
The tone of the keypad sounder may be adjusted by pressing and holding the [#] key. After 2 seconds, the sounder will begin to beep. With each beep, the tone or pitch of the beep will increase or decrease. When the desired tone is achieved, release the [#] key. To adjust the tone in the opposite direction, release the [#] key, and then press and hold the [#] key again.

We offer Secure online payment

Make your payments anytime using our online payment system via Paypal.
Click here for more info.